To order call 1-800-514-9506
This unit will convert the Red, Green and Blue video signals coming out of a video game and convert it into the Composite NTSC video, S-Video, or Component output.
It allows you to plug a Video arcade game board into a regular TV receiver that accepts video, S-Video, or Component input in the NTSC encoding format.
This board ONLY works with standard resolution arcade boardsets ( 15kHz horizontal line frequency ) it is NOT designed for medium resolution games or for VGA cards.
This board is aimed at the arcade hobbyist and home enthusiast, it is NOT designed for commercial, automotive, medical or any use outside the home. It's designed as a tool for other arcade hardware fanatics.
This unit is not recommend to anyone who is inexperienced with the hook up and wiring of arcade games. It's extremely easy to make mis-connections and destroy the arcade board, the converter, the TV and the power supply.
It's ideal for connecting standard resolution JAMMA arcade games to a TV.
Red, Green, Blue video 1volt p-p.
Negative Composite Sync
5v regulated DC @ 180mA
- normally using the same supply as the game board.
Composite Video (Phono Plug)
Composite & S-Video (4 pin header)
S-Video (Standard 4 pin S-Video)
Component (Phono Plugs)
Component (4 pin header)
RGB input level controls For matching RGB input levels to video game boards with high outputs.
Circuit diagrams/Schematics and parts lists are NOT available.
RGB -> TV Converter
This device is designed to take the Red, Green, Blue and synchronization signals from an video arcade game board and convert them into a NTSC video signal.
This means you can use the video encoder to convert video output from an arcade game PCB and display it on a regular TV set, which has Video, S-Video, or Component input.
The converter can be used with a wide variety of game boards, testing has being carried out on a large selection of games to ensure compatibility. Almost any standard resolution JAMMA game will work with the encoder. HOWEVER as variations in video & sync. output vary greatly across game boards not every game can be guaranteed to work with the encoder.
To work with the unit, games MUST have:
Typically these signals are available on a standard
resolution JAMMA gameboard.
The vast majority of JAMMA games of the 1980's and 1990's are standard resolution and should work without problem.
No, the unit requires a standard resolution video signal with 15kHz Horizontal synchronization. VGA resolutions are of 31kHz or higher line rate and EGA/Medium res of 25kHz line rate, the unit DOES NOT convert VGA frequency signals.
It is NOT compatible with VGA/ EGA or Medium Resolution video signals it is strictly Standard Resolution only !
The TV MUST have either composite Video input, a
S-Video input, or Component inputs. The converter will not plug into an antenna socket ( the screw on
RCA jack ).
For best possible picture quality please use S-Video connections.
This is totally dependant on which output from the converter that you use and the TV set used.
Composite NTSC video is of SIGNIFICANTLY lower
quality than a dedicated RGB monitor, so do not expect the quality of the output
to rival what can be achieved with an RGB monitor.
S-Video picture is of a much higher quality than composite video, it easily rivals what can be attained with a dedicated monitor. However even this format is not identical to a dedicated monitor. Compared to composite, an S-Video picture is much sharper and lacks artifacts such as 'dot crawl*' !
It's strongly advised for best possible picture quality use S-Video outputs.
Here is the wiring diagram
BE EXTREMELY CAREFUL WHEN CONNECTING THE CONVERTER !!!
ALWAYS check wiring and voltages BEFORE connecting,
mis-wiring of the converter or the game power supply can damage or destroy the
converter, the gameboard and the TV.
Do not guess when making wiring connections !!!
Wiring Colors are:
6 Pin Header
Red = Red video
Brown = Blue Video
Yellow = Green Video
Black = Ground
Orange = Composite Sync
2 Pin Header
Red = 5v DC power - use same
supply as Game PCB
Ground = Ground ( 0v ) - use same supply as Game PCB
NOTE: The video synchronization signal into the converter is designed to a combined ( composite ) Horizontal and Vertical negative sync. It does not support separate Horizontal and Vertical sync. signals.
No, the converter will only convert RGB video into NTSC video, it will not work in reverse and convert an NTSC video image into RGB.
No ! There is no additional processing carried out on the image.
There are no adjustments for picture size or the location of the image on screen. If these need to be changed, because the image does not fit the TV screen, then the TV set needs to be adjusted. The converter has NO controls over these settings.
Some games feature a vertical screen orientation, e.g.
pacman, where the game is designed to run with a monitor which has been rotated
90 degrees ( the monitor is orientated so it is on it's side ).
The converter does not rotate the screen, so that you can display vertical games on a horizontal display.
The only known problems are with later Midway games such as
Smash TV, NBA JAM, Mortal Komat ( 1, 2 & 3 ) . These games use a vertical
sync. frequency of around 56Hz ( the majority of games having a vertical sync of
around 60Hz ). This vertical sync. frequency appears to be incompatible with
some Sony TV sets, most notably the Sony WEGA series. These sets cannot
sync to this frequency and the picture will roll vertically.
This is NOT a problem with the output from the converter is it purely a problem with the TV receiver.
No, schematics & part lists are not available.